不鏽鋼磁力泵使用中環境應小于40℃、電機溫升不得超過75℃。當 不鏽鋼磁力泵 抽吸液面高于泵軸心線時，起動前打開吸入管道閥門即可，若抽吸液面低于泵軸心線時，管道需配底閥。對于輸送液爲易沉澱結晶的介質，使用後應及時清洗，排淨泵内積液。不鏽鋼磁力泵被輸送的(de)介質及其溫度應在泵材允許範圍内。工程塑料泵的(de)使用溫度＜60℃，金屬泵的使用溫度小于100℃，輸送吸入壓力不大于0.2mpa，大工作壓力1.6mpa、密度不大于1600kg/m3,粒度不大于30×10-6m2/s的(de)不含硬顆料和纖維的(de)液體。不鏽鋼磁力泵運行500小時後，應拆軸承和端面動環的磨損情況若軸承和軸套的間隙大于0.5~1mm,葉輪軸向竄動1.5~2mm時，應更換軸承和軸向動環。因 不鏽鋼磁力泵 軸承的冷卻和潤滑是靠被輸送的介質，所以禁止空運轉，同時避免在工作中途停電後再啓動時所造成載時空載運轉(圖\文 xiaojikuaipao.top/index.asp )。
中譯英：
stainless steel magnetic pump in use environment should be less than 40℃, the temperature rise of the motor should not exceed 75℃. when the stainless steel magnetic pump suction the liquid level above the pump axis line, before starting to open the suction pipe valve can be, if the aspiration level below the pump axis line, pipe with valve. for conveying liquid for easy precipitation crystallization medium, should be cleaned after use, drain the fluid pump. stainless steel magnetic pump by transmission medium and its temperature should be allowed to build in the pump range. engineering plastic pump using temperature < 60℃, metal pump use temperature less than 100 ℃, conveying suction pressure is less than 0.2mpa, the maximum working pressure of 1.6mpa, density of not more than1600kg/m3, particle size of no greater than 30× 10-6m2/s excluding hard material and liquid fiber. stainless steel magnetic pump running after 500 hours, remove the bearing and wear rings fixed end if the bearing and sleeve gap is greater than0.5~1mm, the impeller axial1.5~2mm, replace the bearing and the axially movable ring. because stainless steel magnetic pump cooling and lubrication of bearings is to be delivered by the media, so the absolute prohibition of air, while avoiding work during power failure and starts caused by load carrying transfer time.